WATER TREATMENT

RANGE:

QUICK LINKS

NEED HELP?

For advice on the correct product for any application, contact our telephone help line on 01727 875020.

SYSTEMSAFE-DM Inhibitor

NEW 500ml CONCENTRATE now available

SCALE & CORROSION INHIBITOR FOR ALL SYSTEMS

Once a heating system has been power flushed to remove sludge and corrosion deposits, it is important to protect it from further deterioration.

This can be achieved by treating the system water with SYSTEMSAFE-DM, a balanced blend of corrosion and scale inhibitors, formulated to provide complete protection against system corrosion and scale formation.

It gives long term protection to central heating systems, preventing internal corrosion, scale deposition and boiler noises, and extends the life of the system and maintains its operational efficiency.

The formation of black iron oxide sludge, which accumulates in low flow areas to give flow problems and cold spots on radiators, is prevented, as is the electrolytic and oxidic corrosion which leads to localised pin-hole corrosion and leaks.

SYSTEMSAFE-DM may be used with all metals commonly used in heating systems, including iron, steel, brass, copper and aluminium. It is simply added to the heating system and requires no further action.

SYSTEMSAFE-DM has passed the Buildcert/DWTA performance test and approval process, so you can be sure that it will give long term scale and corrosion protection to heating systems.


The Benchmark Scheme aims to improve the standards of installation and commissioning of domestic heating and hot water systems in the UK and to encourage regular servicing to optimise safety, efficiency and performance. Installers are required to carry out installation, commissioning and servicing work in accordance with the Benchmark Code of Practice which is available from the Heating & Hot water Industry Council at www.centralheating.co.uk

Buildcert Logo Benchmark

SystemSafe-DM corrosion inhibitor

  • INSTRUCTIONS
  • PACK SIZES

Application & usage:

Domestic heating systems: 1 litre of SYSTEMSAFE-DM (or 500ml of SYSTEMSAFE-DM CONCENTRATE) is sufficient to treat a typical central heating system of 100 litres capacity (approx 10/12 radiators). Further addition will only be required if water losses from the system occur, and should be added at a dosage rate of 1 litre per 100 litres system capacity.

To ensure that all SYSTEMSAFE-DM enters the system, add to the feed and expansion tank after isolating water supply and draining off 15 litres (3 gallons) of water. Allow system to re-fill.

Alternatively, SYSTEMSAFE-DM may be introduced directly into a radiator, using a SYSTEMSURE injector unit.

New Systems: Before adding SYSTEMSAFE-DM to a new system, we recommend a pre-commission cleanse with SYSTEM PRE-CLEAN to remove installation and manufacturing debris such as swarf, grease and jointing paste, to mobilise and remove any dust and dirt, and neutralise any acidic flux residues.

Existing Systems: It should be noted that no corrosion inhibitor can reverse previous corrosion damage. To optimise the system efficiency, and allow SYSTEMSAFE-DM to work to best effect, particularly if the water is dirty and heavily discoloured, we advise that the system should first be flushed with HYPER-FLUSH. This is particularly important in cases where a new boiler or heat exchanger is being added to an older installation.

Correct dosage: The exact dosage rate is not critical, as SYSTEMSAFE-DM will work effectively within a +/- 20% range, but a Systemsafe-DM test kit is available to check for the optimum treatment level. The test kit determines the level of molybdate, which will be 330 ppm at the standard dosage rate. The kit contains reagents for approximately thirty tests, together with sampling syringe and test tube with colour chart and instructions.

Click below to download the full Kamco Water Treatment Chemicals data sheet (PDF)

Click here to download the full data sheet/instructions

Available in:

NEW CONCENTRATE

  • Cartons of 12x500ml (BDM007)
  • Cartons of 2x2.5 litre (BDM011) - *** AVAILABLE: APRIL 2015 ***
  • 10 litre drum (BDM008)

Original Formula

  • Cartons of 12x1 litres (BDM002)

Also available:

  • DM Test kit (KTK020)

Technical data:

  • Usage rate: 2.5 to 5% in water
  • Appearance: pink/red liquid
  • Odour: Slightly sweet
  • Density at 20°C: ca. 1.31 g/ml
  • pH of 10% solution: <1.3
  • Solubility in water at 20°C: infinite
  • Max temp: 80°C
  • Comments: non-flammable & non-volatile